Send Message
Home ProductsAdsorption Air Dryer

Desiccant Heatless Adsorption Dryers

Certification
China Suzhou Hongjinli Gas Equipment Co., Ltd. certification
China Suzhou Hongjinli Gas Equipment Co., Ltd. certification
I'm Online Chat Now

Desiccant Heatless Adsorption Dryers

Desiccant Heatless Adsorption Dryers
Desiccant Heatless Adsorption Dryers

Large Image :  Desiccant Heatless Adsorption Dryers

Product Details:
Brand Name: Hongjinli

Desiccant Heatless Adsorption Dryers

Description
Name: Adsorption Air Dryer Dew Point Of Compressed Air: -40℃
High Light:

heatless adsorption dryers

,

Adsorption Desiccant Dryers

,

Desiccant Dryers

Adsorption Air Dryer

 

1. Work flow of heatless regeneration adsorption dryer
The heatless regeneration adsorption dryer uses a pressure swing adsorption regeneration cycle to exchange compressed air through two drying cylinders A and B filled with adsorbent, that is, when one cylinder absorbs water vapor under a high partial pressure (working pressure) state , the other drying cylinder analyzes at low partial pressure (accepts atmospheric pressure), and then switches according to the set time program.

 

Adsorption
The wet air enters the A drying cylinder from the lower pipe diameter through the A1 valve, and then
Flows upward through the adsorbent layer, and the dried air is discharged from the upper piping system.
regeneration
Part of the dry air (about 14%) passes through the upper duct system to regenerate the air
Adjust the valve to enter the B drying cylinder, and the decompressed dry air (called regeneration gas) will analyze and regenerate the adsorbent in the B drying cylinder from top to bottom to restore the drying capacity of the adsorbent. The regeneration gas passes through the lower pipe B2 valve and The muffler vents to the atmosphere.
equalize pressure
After the adsorbent regeneration is completed, the B2 valve is closed and the B drying cylinder
Press to online working pressure and prepare to switch.
switch
The B1 valve of the lower pipe system is open, the A1 valve is closed, and the A2 valve is open.
The two drying cylinders A and B are switched, cylinder B enters adsorption, and cylinder A is depressurized and regenerated. The working sequence and working time are automatically controlled by the controller.

 

heatless/micro heat (LH) regenerative adsorption dryer technical parameters
model air treatment(m3/min) Pipe diameter(mm) Dimensions(length x width x height mm) Heating power/power supply (micro heat) Equipment weight (heatless Kg) Equipment weight (micro heat Kg)
BX0005 0.8 DN15 600X350X1500   70  
BX0010(LH) 1.8 DN20 650X450X1500 0.35/220 80 95
BX0020(LH) 2.8 DN20 700X450X1500 0.5/220 100 120
BX0030 (LH) 3.8 DN25 900X480X1600 0.75/220 130 140
BX0040(LH) 5.5 DN40 1000X650X1750 1.25/220 250 270
BX0060(LH) 6.8 DN40 1000X700X1800 1.5/220 280 300
BX0080(LH) 8.8 DN50 1100X700X1900 2.0/220 450 480
BX0100(LH) 11.5 DN50 1100X650X2050 2.5/220 500 530
BX0120(LH) 14 DN65 1200X850X2200 3.0/380 550 580
BX0150(LH) 16 DN65 1200X850X2200 3.75/380 580 620
BX0200(LH) 22.8 DN80 1400X1000X2350 5.0/380 860 900
BX0250(LH) 28.5 DN80 1400X1000X2500 6.25/380 1200 1250
BX0300(LH) 35 DN80 1750X1100X2500 7.5/380 1600 1700
BX0400(LH) 45 DN100 1700X1100X2600 10/380 1900 2000
BX0500(LH) 55 DN100 1900X1200X2800 12.5/380 2300 2500
BX0600(LH) 65 DN125 2000X1300X2800 15/380 2800 3000
BX0800(LH) 85 DN150 2200X1600X2900 20/380 3400 3800
BX1000(LH) 105 DN150 2600X1600X2960 25/380 4100 4500
BX1200(LH) 120 DN200 3200X1600X3000 30/380 4500 5000
BX1600(LH) 160 DN200 3800X1800X3000 40/380 6000 6500
BX2000 (LH) 200 DN250 4200X2000X3000 50/380 7500 8000
Note: BX0005-BX2000 models are twin-tower traditional structures; (LH) is a low-heat adsorption dryer

Contact Details
Suzhou Hongjinli Gas Equipment Co., Ltd.

Contact Person: Mr. Andy

Tel: +8613812770303

Send your inquiry directly to us (0 / 3000)